找附近的人

<ol id="7vnz7"></ol>

    <font id="7vnz7"></font>

    <form id="7vnz7"><ol id="7vnz7"></ol></form>

        <b id="7vnz7"><var id="7vnz7"><form id="7vnz7"></form></var></b>

            <b id="7vnz7"></b>
            <output id="7vnz7"></output><dfn id="7vnz7"></dfn><b id="7vnz7"></b>

            <ol id="7vnz7"></ol>
            <listing id="7vnz7"><output id="7vnz7"></output></listing>

            你現在的位置:首頁>企業動態>

            濟南雙組份打膠機日常如何進行維護?

            瀏覽:
            1.由于濟南雙組份打膠機密封膠的固化需要一定時間,因此,已涂了雙組份打膠機密封膠的玻璃應水平輕輕搬動.
            1. As the curing time of Jinan two-component sealant is required, the glass coated with two-component sealant should be moved horizontally and gently
            2.雙組份打膠機的A組、B組份膠應保持清潔,嚴防異物進入膠中.
            2. The A and B components of the two-component gluing machine should be kept clean to prevent foreign matters from entering the glue
            3.在連續工作過程中,膠槍每次停止工作時間一般不得超過20分鐘,否則,應用A組份膠沖出全部混合膠,直至單一的A組份膠從槍口排出為止.
            3. In the process of continuous operation, the stop time of glue gun should not exceed 20 minutes each time. Otherwise, all the mixed glue should be flushed out with component a until the single component a glue is discharged from the muzzle

            4.雙組份打膠機的高壓膠管不得強行擠壓、彎曲,防止影響系統正常工作.
            4. The high pressure hose of the two-component gluing machine shall not be forced to squeeze or bend to prevent the normal operation of the system
            5.混膠器應經常保持暢通,以保證良好的出膠效果.如遇堵塞情況,可用丙酮浸泡后清洗.建議每5組清洗一次.
            5. The mixer should always be kept smooth to ensure good glue output. In case of blockage, it can be cleaned after soaking in acetone. It is recommended to clean every 5 groups
            6.當的膠槍長時間不用時(超過一周),應拆下槍體使用溶劑將膠槍和混膠器內的殘留膠體清洗干凈.
            6. When the glue gun is not used for a long time (more than a week), the gun body should be removed and the residual colloid in the glue gun and mixer should be cleaned with solvent
            7.不同雙組份膠生產廠家所生產的膠內含雜質數量不同,根據實際情況清晰B組分的過濾網及單向止回閥,建議每兩組清洗一次
            7. The amount of impurities in the rubber produced by different two-component rubber manufacturers is different. According to the actual situation, the filter screen and one-way check valve of component B should be clear. It is recommended to clean every two groups
            8.定期給各泵的加油口加油,應保證油霧器內不斷油.
            8. Add oil to the oil filler of each pump regularly, and ensure that there is no oil in the atomizer
            了解了濟南雙組份打膠機的日常維護要點后,相信您也懂得了應該怎么來維護您的雙組份打膠機了吧.
            After understanding the daily maintenance points of Jinan two-component gluing machine, I believe you also know how to maintain your two-component glue machine

            上一篇:選用濟南雙份打膠機需要考慮哪些問題?
            下一篇:濟南雙組份打膠機是如何解決漏氣現象的?

            • 官方微信
            找附近的人
            <ol id="7vnz7"></ol>

              <font id="7vnz7"></font>

              <form id="7vnz7"><ol id="7vnz7"></ol></form>

                  <b id="7vnz7"><var id="7vnz7"><form id="7vnz7"></form></var></b>

                      <b id="7vnz7"></b>
                      <output id="7vnz7"></output><dfn id="7vnz7"></dfn><b id="7vnz7"></b>

                      <ol id="7vnz7"></ol>
                      <listing id="7vnz7"><output id="7vnz7"></output></listing>