找附近的人

<ol id="7vnz7"></ol>

    <font id="7vnz7"></font>

    <form id="7vnz7"><ol id="7vnz7"></ol></form>

        <b id="7vnz7"><var id="7vnz7"><form id="7vnz7"></form></var></b>

            <b id="7vnz7"></b>
            <output id="7vnz7"></output><dfn id="7vnz7"></dfn><b id="7vnz7"></b>

            <ol id="7vnz7"></ol>
            <listing id="7vnz7"><output id="7vnz7"></output></listing>

            你現在的位置:首頁>企業動態>

            打膠機點膠針筒應怎樣清洗?

            瀏覽:
            打膠機長期使用之后一定要注意清洗點膠針筒,不然殘留的膠水造成固化、堵塞等問題都會影響到設備的打膠效果,打膠機點膠針筒應怎樣清洗?
            After a long-term use of the glue dispenser, attention must be paid to cleaning the dispensing syringe. Otherwise, problems such as solidification and blockage caused by residual glue will affect the gluing effect of the equipment. How should the dispensing syringe of the dispenser be cleaned?
            打膠機點膠針筒清洗的三種方法:
            Three cleaning methods for dispensing syringe of glue applicator:
            常用清洗方法:首先要了解點膠針筒清洗的原因,簡單的方式就是在膠水沒有固化之前進行清洗,這時可以使用一些稀釋溶液,雙組份打膠機批發,這樣就可以把膠水部分性質破壞然后進行清洗,只需把內部溶液倒出即可,這是比較方便的點膠針筒清洗!
            Common cleaning methods: first of all, we should understand the reasons for the cleaning of dispensing syringe. The simple way is to clean before the glue is solidified. At this time, we can use some diluted solution and wholesale the two-component glue applicator. In this way, we can destroy the properties of the glue and then clean it. Just pour out the internal solution. This is a more convenient way to clean the dispensing syringe!

            固化之后的清洗方法:針筒固化之后,基本無法進行涂膠,這時是必須要對點膠針筒進行處理。不過膠水固化之后對清洗造成一定的難度,需要采用特殊的化學物質溶液,將膠水化學分子打破,這時候才能進行清洗!
            Cleaning method after curing: after the needle cylinder is solidified, it is basically impossible to apply glue. At this time, the dispensing syringe must be treated. However, it is difficult to clean after the glue is solidified. Special chemical solution should be used to break the chemical molecules of the glue. At this time, the cleaning can be carried out!
            清洗方法:使用綠色循環液進行清洗,這種方法是既簡單又有效果,清洗效果特別快而且干凈,對于涂膠作用影響低,可以保持打膠機良好的使用狀況,是劃算、安全的清洗方式,這種清洗方式能夠廣泛適用不同類型的打膠機設備!
            Efficient cleaning method: use green circulating liquid for cleaning. This method is simple and effective. The cleaning effect is very fast and clean. It has a low impact on the gluing effect. It can keep the good service condition of the gluing machine. It is a cost-effective and safe cleaning method. This cleaning method can be widely applied to different types of gluing machine equipment!

            上一篇:如何解決中空玻璃打膠機的磨損情況呢?
            下一篇:最后一頁

            • 官方微信
            找附近的人
            <ol id="7vnz7"></ol>

              <font id="7vnz7"></font>

              <form id="7vnz7"><ol id="7vnz7"></ol></form>

                  <b id="7vnz7"><var id="7vnz7"><form id="7vnz7"></form></var></b>

                      <b id="7vnz7"></b>
                      <output id="7vnz7"></output><dfn id="7vnz7"></dfn><b id="7vnz7"></b>

                      <ol id="7vnz7"></ol>
                      <listing id="7vnz7"><output id="7vnz7"></output></listing>