找附近的人

<ol id="7vnz7"></ol>

    <font id="7vnz7"></font>

    <form id="7vnz7"><ol id="7vnz7"></ol></form>

        <b id="7vnz7"><var id="7vnz7"><form id="7vnz7"></form></var></b>

            <b id="7vnz7"></b>
            <output id="7vnz7"></output><dfn id="7vnz7"></dfn><b id="7vnz7"></b>

            <ol id="7vnz7"></ol>
            <listing id="7vnz7"><output id="7vnz7"></output></listing>

            你現在的位置:首頁>企業動態>

            雙組份打膠機設備注油的保養

            瀏覽:
            雙組份打膠機設備用時間長了,難免有一定程度的磨損,如同人一樣需要身體的檢查和保養,加油就是其中一項必不可少的保養措施。注油對延長打膠機設備的使用壽命,降低磨損帶來的打膠機設備故障都很有好處。
            The equipment of the two-component gluing machine has been used for a long time, so it is inevitable to have a certain degree of wear and tear. If you are the same as a person, you need to check and maintain your body. Refueling is one of the essential maintenance measures. Oil injection is very good for prolonging the service life of the glue machine and reducing the equipment failure caused by abrasion.
            雙組份打膠機安全閥的加油很簡單,在日常保養中為防止生銹、老化,可以直接用油槍的油嘴對準安全閥的注油孔直接加油; 雙組份打膠機電機的加油。
            It is very simple to add oil to the safety valve of the two-component glue applicator. In order to prevent rust and aging during daily maintenance, the nozzle of the oil gun can be directly aligned with the oil filling hole of the safety valve, and the motor of the two-component glue applicator can be refuelled directly.

            油霧器不滴油或者電機在嚴重缺油時,可以將主電機進氣管與電機連接處的活接拆掉,再用油槍想里面加油,輔料電機則可將其端蓋螺母擰開加油。在主電機和輔料電機的進氣口配有油霧器,在發現油位刻度到達低端刻度時應該及時拆下油杯為其加注10#機油;
            When the oil mist eliminator does not drip oil or the motor is seriously short of oil, the union at the connection between the main motor air inlet pipe and the motor can be removed, and then the oil can be filled with oil through the oil gun. For the auxiliary material motor, the end cap nut can be unscrewed for oil filling. The oil atomizer is equipped at the air inlet of the main motor and auxiliary motor. When the oil level reaches the low level, the oil cup should be removed in time to fill with 10% oil;
            雙組份打膠機泵機的加油。
            Two component glue machine pump refueling.
            打膠機設備使用一段時間之后,經常會有膠撥那個里面滲出流到油碗中,這個時候我們需要把膠清理干凈,然后為主泵和輔料泵加好機油。待到機油加好之后,用螺絲刀頂住泵機油碗下面的圓孔,按照順時針方向對油碗進行緊固,配比泵的油碗直接用扳手緊固好就可以了。
            After using the glue machine for a period of time, there is often leakage from the rubber paddle into the oil bowl. At this time, we need to clean up the glue, and then add oil to the main pump and auxiliary pump. After the oil is added, use a screwdriver to counter the round hole under the oil bowl of the pump, and tighten the oil bowl in a clockwise direction. The oil bowl of the matching pump can be directly tightened with a wrench.

            上一篇:打膠機點膠針筒應怎樣清洗?
            下一篇:最后一頁

            • 官方微信
            找附近的人
            <ol id="7vnz7"></ol>

              <font id="7vnz7"></font>

              <form id="7vnz7"><ol id="7vnz7"></ol></form>

                  <b id="7vnz7"><var id="7vnz7"><form id="7vnz7"></form></var></b>

                      <b id="7vnz7"></b>
                      <output id="7vnz7"></output><dfn id="7vnz7"></dfn><b id="7vnz7"></b>

                      <ol id="7vnz7"></ol>
                      <listing id="7vnz7"><output id="7vnz7"></output></listing>